Quick Install Guide Wireless N /Wired PTZ H.264 Network Camera
This document wil guide you through the basic instal ation
process for your new D-Link Network Camera. DCS-5605/5635
Documentation also available on CD
and via the D-Link Website L I S H DCS-5605/5635 Quick Install Guide G
This installation guide provides basic instructions for installing the DCS-5605/5635 Network E N
Camera on your network. For additional information about how to use the camera, please refer
to the User Manual which is located on the CD or from the D-Link support website. Installation Steps
1. Verify the package contents against the list below
2. Hardware Overview
3. Hardware Installation
4. Configuration with the Setup Wizard Package Contents
â€¢ DCS-5605/5635 Network Camera
â€¢ CD-ROM (Software and User Manual)
â€¢ CAT5 Ethernet Cable
â€¢ Power Adapter
â€¢ Two Antennas (DCS-5635 only)
â€¢ A/V Cable
â€¢ Mounting Screws
If any of the above items are missing, please contact your reseller. 2 D-Link DCS-5605/5635 Quick Install Guide
2 E N Hardware Overview G L I Rear Panel S H 1
WPS 12V 2A ETHERNET
LINE/VIDEO MIC RESET
OUT 9 2 3 4 5 6 7 8 9 1 Micro SD Port
Insert a Micro SD memory card to save data from the camera.
Press the WPS button to automatically connect to a 2 WPS (DCS-5635 Only)
WPS-enabled wireless router or access point and establish
connectivity. 3 Power Receptor
Plug in the supplied power adapter to an outlet.
Connect an Ethernet cable to a router, switch, or computer. The 4 Ethernet Port
Ethernet port can also be used to power the camera using a Power
over Ethernet (PoE) switch or router (DCS-5605 only).
The camera provides a terminal block with two pairs of connectors
situated on the back panel. One pair is for input and the other 5 I/O Connector
is for output. The I/O connectors provide the physical interface
to send and receive digital signals to a variety of external alarm
devices. Please refer to the I/O Connector section in the manual
for detailed information. 6 Video/Audio Line-Out Port
Plug the included A/V cable into the A/V out connector to use the
camera with a television or VCR, or connect to speakers. 7 External Microphone Port
Insert an external microphone to record audio. 8 Reset Button
Press and hold for 10 seconds to reset the camera back to the
default settings. 9 Antennas (DCS-5635 Only)
Locate the antennas included with your DCS-5635, and attach
them to the antenna connectors located on the back of DCS-5635. D-Link DCS-5605/5635 Quick Install Guide 3
3 Hardware Overview L I S H G Front Panel E N 1 2 3
The WPS LED will blink blue when initializing a connection,
and il uminate with solid blue once the connection has been 1 WPS/Link LED
established (DCS-5635 only).
The Link LED will illuminate green once a connection has
been established. 2 Microphone
The built-in microphone can be used to capture audio from
sources nearby the camera. 3 Power LED
The Power LED will illuminate red when the camera is
receiving power. 4 D-Link DCS-5605/5635 Quick Install Guide
E N Hardware Installation G L I S Basic Connection H
Connect the camera to your switch or router via Ethernet cable and then connect the supplied
power cable from the camera to a power outlet. Note: Once power has been established, the Power LED will turn red. When the device has
obtained an IP address and is accessible, the Link LED will turn green. D-Link DCS-5605/5635 Quick Install Guide 5
Configuration with Wizard L I S H Configuration G
Insert the DCS-5605/5635 CD into your computer's CD-ROM drive to begin the installation.
If the Autorun function on your computer is disabled, or if the D-Link Launcher fails to start E N
automatically, click Start > Run. Type D:\autorun.exe, where D: represents the drive letter of
your CD-ROM drive.
1. Click Installation Wizard to begin the installation. Install
the Setup Wizard SE and execute the program.
2. The Setup Wizard will appear and display the MAC address
and IP address of your camera(s). If you have a DHCP server
on your network, a valid IP Address will be displayed. If
your network does not use a DHCP server, the camera's
default static IP 192.168.0.20 will be displayed.
Click the Wizard button to continue.
3. Enter the Admin ID and password. When logging in for the first
time, the default Admin ID is admin with the password left blank.
Click Next to proceed to the next page.
4. Select DHCP if your camera obtains an IP address automatically
when it boots up. Select static IP if the camera will use the same IP
address each time it is started.
Click Next to proceed to the next page.
5. Take a moment to confirm your settings and click Restart to
reboot the camera. 6 D-Link DCS-5605/5635 Quick Install Guide