*Using a power supply with a different voltage rating will damage and void the warranty for this product. If any of the above items are missing, please contact your reseller
The D-Link DI-804V Broadband VPN Router enables your network to connect to the Internet via a secure, private connection using a Cable/DSL modem, such as the D-Link DCM-200 Cable Modem. The Virtual Private Network that is created on the Internet between your home and your office (with a VPN server) is secure from interference when you use the DI-804V.
It is an ideal way to connect your computer to a Local Area Network (LAN). After completing the steps outlined in the Quick Install Guide (included in your package) you will have the ability to share information and resources, such as files and printers, and take full advantage of a âconnectedâ environment for work or play!
Connect the WAN port on the DI-804V to the Cable/DSL modem (e.g., the DCM-200) using an Ethernet cable. Your entire LAN can now access the Internet using just one Internet account. The DI-804V has 4 LAN ports. That means that 4 computers can share the benefits of the DI-804V- equipped network.
For the price of one Internet account, the DHCP-capable DI-804V will automatically provide unique IP Addresses for all the computers on the network. (DHCP stands for Dynamic Host Configuration Protocol. It is a protocol for assigning IP Addresses automatically. With a DHCP router like the DI-804V, there is no need to assign static IP Addresses, or purchase multiple addresses from the ISP - Internet Service Provider.)
Everyone in your home can access the Internet on his or her own computer, at the same time, without any noticeable decrease in speed.
With the serial port, you can connect an analog modem (dial-up modem) as a back up in case of any difficulties that may arise with the Cable or DSL connection.
With Firewall Protection, Hacker attack logging, and Virtual Private Networking, the DI-804V provides a level of security suitable for many businesses.
4 This manual provides a quick introduction to network technology. Please take a moment to read through this manual and get acquainted with your DI-804V.
LAN (1-4) LINK (Green) Green LED will LIGHT when link is
(Green) Green LED will BLINK when packet is
transmitting or receiving.
Serial (Green) Green LED will LIGHT when a good link is
WAN (Green) Green LED will LIGHT when a good link is
Status (Yellow) Yellow LED will BLINK when started up
and when firmware is upgraded.
Red LED will LIGHT when powered ON.
Power (5V DC) Connect the DC power adapter to the Power port WAN
Connect DSL/Cable modem to the WAN Ethernet port
Connect a 56k modem/ISDN TA to the serial port
Connect networked devices such as computers and ftp servers to the four LAN ports, which support auto crossover
To reload the factory default settings, press the reset button for 5-6 seconds. Pressing the Reset button will clear the current data.
Provides Virtual Private Networking when communicating with a VPN server- equipped office, or with another DI-804V-equipped network. Supports PPTP and L2TP pass through function.
DSL/Cable Modem support
The DI-804V can connect any DSL/Cable Modem to the network.
The DI-804V is a DHCP-capable router. It automatically assigns unique IP Addresses to each network users that is connected to the DI-804V, for the price of one Internet account.
6 Firewall Protection
Supports general hacker attack pattern monitoring and logging
Supports PPPoE client function to connect to the remote PPPoE server.
Allows the internal server to be accessible from the Internet
Upgradeable New Features
Allows new features to be added in the future
High Performance 32 bit RISC CPU Engine
With the most advanced 32 bit RISC CPU Engine, DI-804V guarantees full compatibility with future DSL/Cable technologies
(DES, 3DES, MD5, SHA-1)
Set a specified idle-time before automatically disconnecting
Eliminates the need for Dial-up. Automatically logs in to your ISP
May connect to a 56k modem or ISDN TA (should a Cable/DSL connection be unavailable or fail.)
No software installation required. Can be configured through a web browser making it OS independent
7 IP Address Settings and Computer Settings
In order to install the DI-804V you will need to check your computerâs settings and the values from your ISP.
The information offered by your ISP:
â˘ Dynamic IP settings â˘ Your fixed IP address for the gateway â˘ Your subnet mask for the gateway â˘ Your default gateway IP address â˘ Your DNS IP address
If you would like to use PPPoE, you will need the following values from your ISP in order to install your router:
â˘ User Name â˘ Password
The static IP settings for the PC:
â˘ Your PCâs fixed IP address â˘ Your PCâs subnet mask â˘ Your PCâs default gateway â˘ Your PCâs primary DNS IP address
Note: The routerâs default IP address setting is 192.168.0.1.
Dynamic IP Settings:
The dynamic IP settings for the PC. It is recommended that you leave your IP settings as automatically assigned. By default, the gateway is a DHCP server, and it will give your computer the necessary IP settings.
8 Using the Configuration Utility
Launch your web browser and type the device IP address (http:// 192.168.0.1) in the browserâs address box. This IP address is the default value of your gateway. Press Enter.
Note: Please make sure that the computerâs IP Address is in the same IP Address range as the DI-804V. The IP Address of the DI-804V is 192.168.0.1. All computers on your network must be within that range, for instance, the computer IP Address could be 192.168.0.x. All computers on the network must have the same subnet mask.
The main menu appears showing all the settings available.
9 Basic Setup
Basic setup is a step-by-step process that will let you input all the basic settings.
Click BASIC SETUP
A username and password screen will appear. Leave the password box empty and type admin (the default username) in the username box. Click OK
The Setup Wizardâs page will appear.
Note: If you choose to input a password at any time, please remember it. If you should lose the password, you will need to reset the unit. After you reset the DI-804V, all your settings will be lost and will need to be re-input.
10 Time Settings Please choose your local time zone.
Device IP Settings
You have to give your VPN Gateway an IP address on your network. This is not the IP address from your ISP but the local internal LAN IP address. The IP address â192.168.0.1â is the default value of your gateway.
Device IP Address: The internal LAN IP address of your VPN Gateway.
Device IP Subnet Mask: The subnet mask can usually be left as its default entry â255.255.255.0â.
11 Cable/DSL ISP Settings
To use the xDSL/Cable ISP settings, you must configure the router. ISP use either static or dynamic IP addresses. Check with your ISP if you are not certain which one it uses. If your ISP uses a static IP address, it means that the IP address of your router is always the same. Most ISPs use dynamic IP addresses. They assign you a new IP address every time you connect to the Internet.
If you have a static IP address, do the following:
Enter the IP address that your ISP provided. Enter the IP subnet mask. Enter the ISP gateway address. Enter the DNS IP address.
12 ISP Additional Settings (PPPoE Settings)
You can configure the router to use additional ISP settings. Some ISPs require PPPoE for authentication purposes.
Do the following to set up PPPoE:
User name: Enter the user name of your ISP account. Password: Enter the password of your ISP account. Retype password: Enter the password of your ISP account again to re- confirm. Some ISPs use Host Name and Domain Name to authenticate the user; if this is the case, you need to enter: Host Name: Enter the name of the gateway. Domain Name: Enter the domain name provided by your ISP Some ISP require you input the LAN card Mac address; if this is the case, you need to enter: Mac Address: Enter this LAN card Mac address.
Note: Some ISPs may recognize your LAN card Mac address as a legal user; in this case, you have to copy the LAN card Mac address in the Mac address field. For WIN 95/98 you can run winipcfg to see the LAN card Mac address. For WIN/NT you can run ipconfig/all to see the LAN card Mac address.
13 Modem Settings
The modem dialup can be used as a backup for the xDSL/Cable connection. If you would like to use the modem dialup or VPN features you must enable the modem settings. Click on the Advanced Settings tab and enter the ISP account information.
Note: If you would like to change the baud rate settings, please click on the âADVANCED SETTINGSâ. Then click on the MODEM SETTINGS button. Note: When your Cable/DSL connection comes back on-line, you will need to return to this page and uncheck the backup dial-up modem setting in order to use your Cable/DSL Broadband connection again.
14 VPN Settings
Use this screen to enable the IPSec feature. This feature allows a secure connection between two parties. The connection is made over the Internet. To enable the VPN function, check the Enable VPN checkbox and enter a string into the connection name field, then click the âADDâ button.
Enabled NetBIOS Broadcast
Computers running Microsoft Windows can communicate with one another using NetBIOS. Users can access remote network resources by browsing the Window Network Neighborhood. You can uncheck the Enabled NetBIOS Broadcast checkbox. The Secure Association (SA) can be created using IKE (auto-mode) or Manual Mode. The default value is Internet Key Exchange (IKE). If you would like to use Manual Key, check the Manual radio box and required input fields will be shown.
Enter the Incoming SPI that the remote VPN Gateway will use to identify this SA.
Enter the Outgoing SPI that the local VPN Gateway will use identify this SA
VPN Internet Gateway supports three encryption algorithms (Null, DES, or 3DES); user can select an appropriate encryption algorithm.
This string is used as a key to encrypt and decrypt the data transmitted.
VPN Internet Gateway supports two authentication algorithms (MD5 or SHA-1); user can select an appropriate authentication algorithm.
This string is used as key authentication.
16 Save & Restart
After you have finished making all the changes on the various pages, please click Save & Restart to save the settings and restart the device. After the restart, the device will function according to the saved settings.
During the startup process the LED of the device will blink. Please wait until the blinking of the device stops before proceeding.
17 Device Information Device information displays the current settings of the VPN Internet Gateway.
This is the host name of the VPN Internet Gateway.
This is the IP address of the VPN Internet Gateway.
Private LAN Mac Address
This is the Mac address of the VPN Internet Gateway LAN port.
Public WAN (xDSL/Cable) Mac Address
This is the Mac Address of the VPN Internet Gateway WAN Ethernet port.
Displays the Firmware Version of the DI-804V and its release date
18 Device Status Device status displays the current connection status of the VPN Gateway. Modem Dialup
The modem can be used as a dialup backup for the xDSL/Cable connection. If modem dialup is connected, it will show âModem: Active,â otherwise it will show âNot Activeâ.
Shows the Device IP address, private LAN Mac address and public WAN Mac address of the VPN Internet Gateway.
Release and Renew
Click Release button, the VPN Internet Gateway will disconnect with the xDSL/Cable modem. Click the Renew button, the VPN Internet Gateway will connect with the xDSL/Cable modem again. DHCP Log
Click DHCP Log button, the screen will display the current DHCP client information.
Click VPN Status button, the screen will display the current VPN connection information.
19 Advanced Settings Advanced settings include DHCP server, virtual server static routing, dynamic routing, filter settings, modem string settings and administration settings.
A username and password will appear. Type âadminâ in the user name box, and type the password that you have set the device (the default is no password) Click OK The Advanced Settings page will appear.
DHCP Server Settings The VPN Internet Gatewayâs DHCP server is enabled by default. If you would like to disable the DHCP server, unclick on the square circle below.
20 IP Address Pool Range
The IP address pool contains the range of the IP address that will automatically be assigned to the clients of your network. Default setting is from 192.168.2.2 to 192.168.2.100. IP Address Reservation
You can use IP address reservation option to give particular computers on your network the same static IP address every time the computer is turned on. Virtual Server Settings Virtual server settings allow clients on the Internet to access your LAN via the Internet. You can use the IP mapping function to access an FTP server or Telnet server etc. remotely through Internet.
DMZ function can be applied to a single client behind the VPN Gateway to expose it to the Internet and ensure complete Internet application compatibility even if specific ports are not known. If you would like to enable DMZ function, enter an IP address into the DMZ IP field. The value of â0â means that the DMZ function is disabled.
21 Static Routing Static routing settings allow the VPN Internet Gateway to route IP packets to another network. The routing table stores the routing information so that your network device knows where to redirect the IP packets to the proper network.
Destination IP Address
The destination IP is the address of the remote network to which you want to assign a static route.
The subnet mask of your network IP address.
Gateway IP Address The IP address of the interface used to link to the remote network.
Dynamic Routing Dynamic Routing Settings allow the VPN Internet Gateway to route IP packets to another network automatically. The RIP protocol is applied, and broadcasts the routing information to other routers on the network regularly.
22 For the SEND option choosing the proper protocol by which you transmit the data on the network.
For the RECEIVE option choosing the proper protocol by which the VPN Internet Gateway receive the data on the network.
Filter Settings â LAN Filter Settings LAN Filter Settings allow administrator to define whether local user has the permission to access Internet. To activate this feature, check LAN Side Filter Enabled. Then, you can define the filtering policy by entering an IP address range, network port number and select the protocol(s).
For example, to prevent the local user of IP address range (from 101 to 200) to access port 80 (HTTP), the settings are as follows,
LAN Side Filter Enabled: Enabled Default LAN Side Filter: Pass Filter: Block Protocol: TCP IP Address Range: 101 ~ 200 Destination Port Range: 80 ~ 80 (HTTP)
23 Filter Settings â WAN Filter Settings WAN Filter Settings allow administrator to define whether remote/outside user has the permission to access the local network. To activate this feature, check WAN Side Filter Enabled. Then, you can define the filtering policy by entering IP address range, the port range and select the protocol(s).
For example, to prevent the remote user of IP address range (184.108.40.206 to 220.127.116.11) to access virtual WEB server (port 80), the setting are as follows,
WAN Side Filter Enabled: Enabled Default WAN Side Filter: Pass Filter: Block Protocol: TCP IP Address Range: 18.104.22.168 to 22.214.171.124 Destination Port Range: 80 ~ 80 (HTTP)
24 Modem String Settings Modem string settings allow user to input detail settings for the analog modem. If you would like to change the baud rate settings, please check the initial string. (You can refer to the manual for your modem.)
Administration Settings PASSWORD SETTINGS
You can give your VPN Gateway a new password. This password will be required the next time you configure your VPN Gateway. To enter a password, type your password in the new password field and type it again in the retype password field.
Note: it is important to remember your password. If for any reason you lose or forget your password, press the small reset button located on the back of the device for 5 to 6 seconds. Reset action will re-initialize the settings. All configurations, including password, will be reset and require re-entering.
25 SYSTEM ADMINISTRATION
Here, remote users can be set up to configure and administrate the VPN Internet Gateway through Internet. The default value of HTTP port is 80. The default IP address of remote administration host is: 0.0.0.0. (IP address of 0.0.0.0 means that any PC on the network can remote access and manage the VPN Internet Gateway).
If you use this function, you have to enable the feature âAllow remote user to configure the deviceâ first. Once you have enabled this function, type the VPN Internet Gateway WAN IP address (http://192.168.100.1:1023) into the browser of any or specific PC on the network.
26 Note: Once HTTP port no (NOT PORT 80) is changed and the users of the LAN terminal want to configure the VPN Internet Gateway, the users have to type the VPN Internet Gateway LAN IP address with port number (http://192.168.0.1:1023).
System Parameters allows user to setup the MTU value (Maximum Transmission Unit). The default MTU value is 1500 Bytes. User can setup a proper MTU for your network device.
For some areas, the ISPs set the limit packet size for PPPoE connection. User has to change MTU setting for surfing the net.
27 Save & Restart If you have finished making all the changes on the various pages, please click Save & Restart to save the settings and restart the device. If you would like to configure the setting again, you can browse those functions then click them. After the restart, the device will function according to the saved settings.
Save & Restart lets you save the input settings to the VPN Internet Gateway (so as to be retrieved at a later time) and then restart it.
28 System Tools System Tools
Detects the status of the VPN Internet Gateway.
Intruder Detection Log The event messages show the possible hacker attacks that have occurred on your VPN Gateway. Up to 32 hacker attacks may be logged in this manner.
Display Routing Table The Display Routing Table shows the current static routing configuration.
29 System Diagnostics System diagnostics shows your VPN Gatewayâs information. It will perform a check-up on your VPN Gateway to make sure that everything is functioning properly.
30 Save Settings This allows you to save the configuration to a file. If you would like to do this, click Save File to save your current settings to a file. Then click save this file to disk in the browsing wizard.
31 Load Settings - Load Default Settings This allows you to load the original default settings of your VPN Internet Gateway.
Load Settings - Load Settings From File This allows you to load the settings from a file.
32 Upgrade Firmware The upgrade firmware option allows you to upgrade the latest firmware to your VPN Internet Gateway.
Reset Device Resetting the device will restart it. Click on the START button to restart.
33 Configuring Your PCs to Connect to the DI-804V Router
If you do not wish to set the static IP address on your PC, you will need to configure your PC to request an IP address from the gateway.
Click the Start button, select Settings, select Control Panel. Double-click the Network icon. In the configuration tab, select the TCP/IP protocol line that has been associated with your network card/adapter. If there is no TCP/IP line listed, you will need to install TCP/IP now.
34 Click the Properties button, then choose the IP ADDRESS tab. Select Obtain an IP automatically.
After clicking OK, windows might ask you to restart the PC. Click Yes.
CONFIRM YOUR PCâS IP CONFIGURATION
There are two tools which are great for finding out a computerâs IP configuration: MAC address and default gateway.
â˘ WINIPCFG (for Windows 95/98)
Inside the windows 95/98 Start button, select Run and type winipcfg. In the example below this computer has an IP address of 192.168.0.100 and the default gateway is 192.168.0.1. The default gateway should be the network device IP address. The MAC address in windows 95/98 is called the Adapter Address.
NOTE: You can also type winipcfg in the DOS command prompt.
â˘ IPCONFIG (for Windows 2000/NT/XP)
In the DOS command prompt type IPCONFIG and press Enter. Your PC IP information will be displayed as shown below.
36 Networking Basics
Using the Network Setup Wizard in Windows XP
In this section you will learn how to establish a network at home or work, using Microsoft Windows XP. Note: Please refer to websites such as http://www.homenethelp.com and http://www.microsoft.com/windows2000 for information about networking computers using Windows 2000, ME or 98.
Go to START>CONTROL PANEL>NETWORK CONNECTIONS Select Set up a home or small office network
When this screen appears, Click Next.
37 Please follow all the instructions in this window:
Click Next In the following window, select the best description of your computer. If your computer connects to the Internet through a gateway/router, select the second option as shown.
38 Enter a Computer description and a Computer name (optional.)
Enter a Workgroup name. All computers on your network should have the same Workgroup name.
39 Please wait while the wizard applies the changes.
When the changes are complete, Click Next.
Please wait while the wizard configures the computer. This may take a few minutes.
40 In the window below, select the best option. In this example, âCreate a Network Setup Diskâ has been selected. You will run this disk on each of the computers on your network. Click Next.
Insert a disk into the Floppy Disk Drive, in this case drive âA:â
Format the disk if you wish, and Click Next.
Please wait while the wizard copies the files.
Please read the information under Hereâs how in the screen below. After you complete the Network Setup Wizard you will use the Network Setup Disk to run the Network Setup Wizard once on each of the computers on your network. To continue Click Next
42 Please read the information on this screen, then Click Finish to complete the Network Setup Wizard.
The new settings will take effect when you restart the computer. Click Yes to restart the computer.
You have completed configuring this computer. Next, you will need to run the Network Setup Disk on all the other computers on your network. After running the Network Setup Disk on all your computers, your new wireless network will be ready to use.
43 Naming your Computer
Naming your computer is optional. If you would like to name your computer please follow these directions:
In Windows XP:
Click START (in the lower left corner of the screen) Right-click on My Computer Select Properties
â˘ Select the Computer Name Tab in the System Properties window.
You may enter a Computer description if you wish, this field is optional.
To rename the computer and join a domain,
â˘ Click Change
â˘ In this window, enter
the Computer name.
â˘ Select Workgroup
and enter the name of the Workgroup.
â˘ All computers on
your network must have the same Workgroup name.
â˘ Click OK
45 Assigning a Static IP Address
Note: Residential Gateways/Broadband Routers will automatically assign IP Addresses to the computers on the network, using DHCP (Dynamic Host Configuration Protocol) technology. If you are using a DHCP-capable Gateway/Router you will not need to assign Static IP Addresses. If you are not using a DHCP capable Gateway/Router, or you need to assign a Static IP Address, please follow these instructions:
Go to START Double-click on Control Panel
Double-click on Network Connections
Right-click on Local Area Connections.
Highlight Internet Protocol (TCP/IP)
47 Select Use the following IP address in the Internet Protocol (TCP/IP) Properties window. Input your IP address and subnet mask. (The IP Addresses on your network must be within the same range. For example, if one computer has an IP Address of 192.168.0.2, the other computers should have IP Addresses that are sequential, like 192.168.0.3 and 192.168.0.4. The subnet mask must be the same for all the computers on the network.) Input your DNS server addresses. The DNS server information will be provided by your ISP (Internet Service Provider.)
Click OK You have completed the assignment of a Static IP Address. (You do not need to assign a Static IP Address if you have a DHCP-capable Gateway/Router.)
48 Contacting Technical Support
You can find the most recent software and user documentation on the D-Link website.
D-Link provides free technical support for customers within the United States for the duration of the warranty period on this product.
U.S. customers can contact D-Link technical support through our web site,
or by phone.
D-Link Technical Support over the Telephone: (800) 758-5489
24 hours a day, seven days a week.
D-Link Technical Support over the Internet: http://support.dlink.com
When contacting technical support, please provide the following information:
Serial number of the unit Model number or product name Software type and version number
49 Limited Warranty and Registration
D-Link Systems, Inc. (âD-Linkâ) provides this 1-Year warranty for its product only to the person or entity who
originally purchased the product from:
D-Link or its authorized reseller or distributor.
Products purchased and delivered with the fifty United States, the District of Columbia, US Possessions
or Protectorates, US Military Installations, addresses with an APO or FPO. 1-Year Limited Hardware Warranty: D-Link warrants that the hardware portion of the D-Link products
described below (âHardwareâ) will be free from material defects in workmanship and materials from the date of
original retail purchase of the Hardware, for the period set forth below applicable to the product type (âWarranty
Periodâ). 1-Year Limited Warranty for the Product(s) is defined as follows
Hardware (including power supplies and fans) One (1) Year
Spare parts and spare kits Ninety (90) days.
D-Linkâs sole obligation shall be to repair or replace the defective Hardware at no charge to the original owner.
Such repair or replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement
Hardware need not be new or of an identical make, model or part; D-Link may in its discretion replace the defective
Hardware (or any part thereof) with any reconditioned product that D-Link reasonably determines is substantially
equivalent (or superior) in all material respects to the defective Hardware. The Warranty Period shall extend for an
additional ninety (90) days after any repaired or replaced Hardware is delivered. If a material defect is incapable of
correction, or if D-Link determines in its sole discretion that it is not practical to repair or replace the defective
Hardware, the price paid by the original purchaser for the defective Hardware will be refunded by D-Link upon
return to D-Link of the defective Hardware. All Hardware (or part thereof) that is replaced by D-Link, or for which
the purchase price is refunded, shall become the property of D-Link upon replacement or refund. Limited Software Warranty: D-Link warrants that the software portion of the product (âSoftwareâ) will
substantially conform to D-Linkâs then current functional specifications for the Software, as set forth in the
applicable documentation, from the date of original delivery of the Software for a period of ninety (90) days
(âWarranty Periodâ), if the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Warranty Period, the magnetic media on which D-Link
delivers the Software will be free of physical defects. D-Linkâs sole obligation shall be to replace the non-
conforming Software (or defective media) with software that substantially conforms to D-Linkâs functional
specifications for the Software. Except as otherwise agreed by D-Link in writing, the replacement Software is
provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for
the Software. The Warranty Period shall extend for an additional ninety (90) days after any replacement Software is
delivered. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion
that it is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-
conforming Software will be refunded by D-Link; provided that the non-conforming Software (and all copies
thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given
automatically terminates. What You Must Do For Warranty Service:
Registration is conducted via a link on our Web Site (http://www.dlink.com/). Each product purchased must be
individually registered for warranty service within ninety (90) days after it is purchased and/or licensed.
FAILURE TO PROPERLY TO REGISTER MAY AFFECT THE WARRANTY FOR THIS PRODUCT.
Submitting A Claim. Any claim under this limited warranty must be submitted in writing before the end of the
Warranty Period to an Authorized D-Link Service Office.
The customer must submit as part of the claim a written description of the Hardware defect or Software
nonconformance in sufficient detail to allow D-Link to confirm the same.
The original product owner must obtain a Return Material Authorization (RMA) number from the
Authorized D-Link Service Office and, if requested, provide written proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) before the warranty service is provided.
After an RMA number is issued, the defective product must be packaged securely in the original or other
suitable shipping package to ensure that it will not be damaged in transit, and the RMA number must be
prominently marked on the outside of the package.
The customer is responsible for all shipping charges to and from D-Link (No CODs allowed). Products
sent COD will become the property of D-Link Systems, Inc. Products should be fully insured by the customer
and shipped to D-Link Systems Inc., 53 Discovery Drive, Irvine CA 92618.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing
requirements, or for which an RMA number is not visible from the outside of the package. The product owner
agrees to pay D-Linkâs reasonable handling and return shipping charges for any product that is not packaged and
shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or non-
conforming. What Is Not Covered:
This limited warranty provided by D-Link does not cover: Products that have been subjected to abuse, accident,
alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service
in any way that is not contemplated in the documentation for the product, or if the model or serial number has been
altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair,
and shipping costs; Operational adjustments covered in the operating manual for the product, and normal
maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage;
and Any hardware, software, firmware or other products or services provided by anyone other than D-Link. Disclaimer of Other Warranties: EXCEPT FOR THE 1-YEAR LIMITED WARRANTY SPECIFIED HEREIN,
THE PRODUCT IS PROVIDED âAS-ISâ WITHOUT ANY WARRANTY OF ANY KIND INCLUDING,
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN
ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT AS EXPRESSLY COVERED UNDER THE LIMITED
WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND
PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT. Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE
UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE
THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY
CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT
NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR
MALFUNCTION, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED
WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM THE
USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING LIMITED WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. GOVERNING LAW: This 1-Year Warranty shall be governed by the laws of the state of California. Some states do
not allow exclusion or limitation of incidental or consequential damages, or limitations on how long an implied
warranty lasts, so the foregoing limitations and exclusions may not apply. This limited warranty provides specific
legal rights and the product owner may also have other rights which vary from state to state. Trademarks
CopyrightÂŽ 2001 D-Link Corporation. Contents subject to change without prior notice. D-Link is a registered
trademark of D-Link Corporation/D-Link Systems, Inc. All other trademarks belong to their respective proprietors. Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to make any derivative such as
translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems Inc., as
stipulated by the United States Copyright Act of 1976. CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the
user may be required to take adequate measures. FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
51 interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Register Your D-Link Product Online at http://www.dlink.com/sales/reg