This product can be set up using Internet Explorer or Netscape Navigator, 6.x or
FXS+FXO VoIP Router
Before You Begin You must have at least the following:
â€§ A subscription with bundled service provider included in this package â€§ A Computer with a CD-ROM drive and an Ethernet port running a Windows â€§ Ethernet based broadband modem
Indicates the unit is powered on. Run
The Run LED will flash when performing a self- test/booting up and light solid green if the self-test or bootup fails. The Alarm LED will light solid red if the self-test or Alarm
bootup fails. The Alarm will flash red when the system is registering with the service provider or register fails. WAN LED
When a connection is established the 10 or 100 LED will light up solid. The LED will blink to indicate activity. If the 10 or 100 LED does not light up when a cable is connected, verify the cable connections and make sure your devices are powered on. LAN LEDs
When a connection is established the 10 or 100 LED will light up solid on the appropriate port. The LEDs will blink to indicate activity. If the 10 or 100 LED does not light up when a cable is connected, verify the cable connections and make sure your devices are powered on. Phone LEDs
This LED displays the VoIP status and Hook activity on
the phone port that is used to connect your normal telephone(s). If a phone connected to a phone port is off hook or in use, this LED will light solid. When a phone is ringing, the indicator will blink. Line LEDs
Light on means the line is in use (off-hook), and vice versa. 2
Connect to your phones using standard phone cabling. Line Ports
Connect to your original telephone line on the wall jack with RJ-11 cable. LAN Port
Connect to your Ethernet enabled computers using Ethernet cabling. WAN Port
Connects to your broadband modem using an Ethernet cable. Reset
This is used to reset the unit to the factory default settings. DC 12V
The power adapter attaches here.
Using a power supply with a different voltage rating will damage this product.
Connecting the DVG-7022S directly to a Modem and Computer
If your computer connects directly to a DSL or Cable modem and does not connect to a router, follow the steps below to install your DVG-7022S. For any other configuration, please refer to the user manual located on the CD-ROM. After the steps are completed, your setup should look similar to the diagram below.
a. Turn off your Computer.
b. Disconnect the power to your Cable/DSL Modem (Unplug or turn off
the power switch).
c. Unplug the existing Ethernet cable that is connected to your
Cable/DSL Modemâ€™s LAN or Ethernet port. Leave the other end of this cable attached to your PC.
d. Plug the Ethernet cable connector that
you just removed from the modem into one of the four LAN ports on the back of the DVG-7022S. The other end remains attached to the PC.
Connecting the DVG-7022S directly to a Modem and Computer (continued)
e. Attach one end of the Ethernet Cable provided in this package to the
LAN or Ethernet Port on the Cable/DSL Modem.
f. Attach the other end of the provided Ethernet
Cable to the WAN Port of the DVG-7022S.
g. Connect a standard analog telephone and the phone port on the rear
panel of the DVG-7022S by the provided phone cable.
h. Connect your original telephone line on the
wall jack and the line port on the rear panel of the DVG-7022S by the provided phone cable.
i. Reconnect the power to the Cable/DSL
Modem (Plug in or turn on the power switch).
j. Connect the Power Adapter to the Power Connecter on the DVG-
k. Connect the other end of the Power Adapter to
an available electrical outlet (Wall Socket or Surge Protector).
If your ISP registers your computerâ€™s MAC address, see the section labeled MAC Cloning for Connections in the user manual on the CD-ROM. PPPoE Users, please continue to the next page for additional configuration steps.
Hardware configuration is complete! If your VoIP service is already activated, you can make phone calls now.
Some Internet Service providers use PPPoE as their method of connecting clients. If you have a PPPoE connection, you must follow the steps below to complete the configuration of your hardware. If you are unsure of your connection type or do not know your username and password, please check with your Internet Service Provider.
Open your Web browser and type http://192.168.8.254 into the URL address box. Press the Enter or Return Key
Click OK to enter Web Site.
Click Network Settings.
Enter PPPoE Account, Password and Confirm Password.
PPPoE Configuration (continued)
Click Accept at the bottom of this page.
Click System Operation at left menu.
Select Save Settings and Restart.
Once the unit reboots you will see the message. Check to see if the status LED light goes from blinking green to solid green on the front panel of the DVG-7022S.
The information found on the Device Information page is necessary for VoIP service registration 7